Good question. If one is out of level I would assume they both are? If one is and one isn’t is something wrong?Alright, fun question.
Where do y’all level your table from? Bubble level on the platter or plinth? I
Platter.Good question. If one is out of level I would assume they both are? If one is and one isn’t is something wrong?
I don’t have your answer I’m genuinely curious too.
I just did the same thing and noticed some pretty immediate reduction in IGD, it’s interesting though cause all turntable set ups guides I’ve gone through say level on the plinth which doesn’t make much sense cause on the platter I’ve always found it to be slightly off by that measure. Just reversed that so the platter is as even through out as possible and the plinth is a little off but still within the little black center bubbleI mean don't get me wrong, if your plinth is way off and your platter is okay then you know, there's probably an issue with your spindle mount... But if the plinth is a little off but the platter is level, I think that's what really matters. I'll go one further and say that I specifically use the bubble level across the arc of the tonearm from the run in to the run out. And I try to make sure that its at it's most level towards the run out, where the album is naturally harder to track. If that arc is level then I don't worry too much about fine tuning the rest of it, because that's the location that really matters, where the stylus hits the groove across the length of the record.
I would imagine that's because most TT manufacturers don't want to suggest that their plinth and platters might not both be completely level. But I mean, I would guess in most cases until you reach pretty high end tables, they're likely to be a little off...I just did the same thing and noticed some pretty immediate reduction in IGD, it’s interesting though cause all turntable set ups guides I’ve gone through say level on the plinth which doesn’t make much sense cause on the platter I’ve always found it to be slightly off by that measure. Just reversed that so the platter is as even through out as possible and the plinth is a little off but still within the little black center bubble
I've used a bubble 'button" level and a bubble app, but I've found a small 6-9" level works best for me. Lay it across the platter going left to right, level, turn the platter so the level is pointing front to back, level again. adjust as needed going back and forth. Since you can't really place the button level dead center on the plinth, and placing it on top of a TT weight or clamp for instance, may reflect imperfections in the weight itself, it seemed easier and more accurate to go with a 9" level.Alright, fun question.
Where do y’all level your table from? Bubble level on the platter or plinth? I
That would be me and I am PUMPED!Did a fellow N&G member snag it?
That would be me and I am PUMPED!
I hear @Manzig is getting me hooked up with a custom "Member's Only" windbreaker too...
Did you get the 20/20 also?That would be me and I am PUMPED!
I hear @Manzig is getting me hooked up with a custom "Member's Only" windbreaker too...
I did not... A Sutherland phono is in my endgame setup wish-list though.Did you get the 20/20 also?
That would be me and I too am PUMPED!Did you get the 20/20 also?
The mofi from Uturn upgrade is still pretty significant. Enjoy !!I did not... A Sutherland phono is in my endgame setup wish-list though.
Pretty excited to hear your thoughts on the StudioDeck! That cart is wicked good, too.I did not... A Sutherland phono is in my endgame setup wish-list though.
I use this little crosscheck bubble level on my platter. It's easier for me to use than a 6" level because I can check for "level-ness" when the platter is turning. $4 at my local hardware store, $10 for the "VPI" version from Music Direct!I've used a bubble 'button" level and a bubble app, but I've found a small 6-9" level works best for me. Lay it across the platter going left to right, level, turn the platter so the level is pointing front to back, level again. adjust as needed going back and forth. Since you can't really place the button level dead center on the plinth, and placing it on top of a TT weight or clamp for instance, may reflect imperfections in the weight itself, it seemed easier and more accurate to go with a 9" level.
For some reason it going across the majority of the platter makes me feel more confident of the results, lol
Just my method
-immediately orders seven VPI versions-$4 at my local hardware store, $10 for the "VPI" version from Music Direct!
I don't even have a table and I almost ordered a few for "just in case". Nice solution.-immediately orders seven VPI versions-
I have this one, $6I use this little crosscheck bubble level on my platter. It's easier for me to use than a 6" level because I can check for "level-ness" when the platter is turning. $4 at my local hardware store, $10 for the "VPI" version from Music Direct!
View attachment 133233
VPI - Crosscheck Turntable Level
The world's largest online retailer of high-end audio, audiophile music, and accessories. We specialize in vinyl records and turntables.www.musicdirect.com
That really is a nice StudioDeck -- I missed the Little Fwend tonearm lifter previously!